Tulip Decor Figurine by 29FLOMakerWorld: Download Free 3D Models

29FLO

Household>Decor

IP Report

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

0.12mm layer, 5 walls, 5% infill

Designer

5.4 h

1 plate

4.6(57)

AMS 3 Color version

7.2 h

1 plate

4.4(36)

Open in Bambu Studio

Boost

1102

1925

115

1.8 k

793

Released

Description

Tulip Decor Figurine

Feel free to scale it as desired. For sure you can make it bigger. If you choose a smaller size, the model will be more prone to damage. Don’t be tempted by a shorter printing time—take your time to print it properly, and you won’t have to print it twice! :)

If reducing print time is absolutely essential for you, you can simply increase the layer height. Just keep in mind that this will also reduce the level of detail.

Be careful when removing supports. Stem might be fragile. Take your time!

Printed with Fuzzy Skin effect.
Fuzzy Skin: All Walls
Fuzzy Skin Point Distance: 0.35
Fuzzy Skin thickness: 0.2

If you're interested in the commercial use of my models, check the link to my Patreon https://patreon.com/29flo

Boost Me (for free)

If you enjoy my work, I’d be so grateful if you showed your support by clicking "Boost." Thank you! 😊

Membership

If you would like to print and sell my models, you can do so through an active subscription

Join

As always!
The key to printing my figurines is having good adhesion to the build plate. I use CryoGrip Pro Frostbite for printing, which provides excellent grip, ensuring that every figurine prints successfully every time. I mainly use filaments from Bambu and have no issues with them either. If you have a different setup, make sure to focus on build plate adhesion, use high-quality dry filament, and everything should be fine.

All my photos are real and show an actual 3D-printed figure photographed by me.

Comment & Rating (115)

@sween

Boosted

Beautiful model. Very fragile. The tree supports were like 2x-3x as thick as the stem lol.

@Kirk2626

that color is perfect what kind is that?

@sween

Boosted

Replying to @Kirk2626 :

It came out really nicely, I got lucky on the color changes. It's SUNLU Silk Rainbow Filament PLA+ Red-Pink-Green-Yellow. It's been difficult to print with, I've had to slow down speeds and tweak support settings to ensure stuff prints properly and doesn't get knocked off the plate during printing. Maybe drying it would help but I don't have a dryer yet. But when it comes out, it looks great.

(Edited)

@Kirk2626

Replying to @sween :

I’m going to get that color for sure ty for responding nice job on your print again

@Kirk2626

Print Profile

0.12mm layer, 5 walls, 5% infill

Turned out perfect you just have to be very careful when you take the trees off. You have to use clipper is very carefully.

The profile uploader has replied

@29flo

Printed two without any issues. Are you using clippers or brute force only? :)

@Kirk2626

Replying to @29flo :

I use the needle nose pliers. I will try again

@29flo

Replying to @Kirk2626 :

Always start clipping where thinest support part is. Usually at the top. Cut one by one. Then move down.

@user_729678468

Print Profile

0.12mm layer, 5 walls, 5% infill

Nice design, colored in studio. Thanks.

@user_2364735783

How do you color the individual parts if it gives them to me as a single object? Thank you

Show original

@user_729678468

Replying to @user_2364735783 :

I used bambu studio. Have your colors loaded in ams, resync colors. Load model, select it, go to paint bucket select that, select color, select hight range, I used 7.5. start at bottom work your way up changing colors as needed. to finish I used the circle tool to color the leaf above the start of the flower. hope this makes sense. good luck.

@Irondork

Print Profile

0.12mm layer, 5 walls, 5% infill

BEAUTIFUL

@DaddyWazzy_TheC

Print Profile

AMS 3 Color version

excellent and I broke it removing the supports. completely my fault

@collective82

Print Profile

AMS 3 Color version

printed the multi color version and it’s really nice.

@Cable

Print Profile

AMS 3 Color version

It looks great! Came out without any issue, was careful removing the supports.

@sandycheeks1972

Mega schön

@pgranlie

Print Profile

0.12mm layer, 5 walls, 5% infill

It took me a few tries. It broke of at when it was like 1 cm left. But I got it to work

@6r0t6G6

Print Profile

AMS 3 Color version

well done…

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Get Commercial License