X1C - P1 Top Glass Riser by Officina23

Officina23

3D Printer>3D Printer Accessories

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

Corner Glass Riser (two colors)

Designer

1.4 h

1 plate

5.0(24)

Corner Glass Riser (single color)

Designer

1.2 h

1 plate

5.0(65)

Optional middle glass riser (single color)

Designer

21 min

1 plate

5.0(3)

Print on A1 mini - 0.24mm layer, 3 walls, 15% infill

2 h

1 plate

5.0(1)

Open in Bambu Studio

Boost

149

153

499

421

Released

Description

After using my perimeter version of the X1C top glass riser for several months (you can find it by clicking here), I designed this variant consisting only of the four corners which therefore does not require any connectors for assembly and has a very short printing time.

You will find two printi profiles for this riser: the main one is to make it in two colors (as in the photo), the other is to print the corners in one color.

Comment & Rating (153)

@hookuum

Print Profile

Corner Glass Riser (single color)

Perfect fit and the extra space is ideal. Thank for sharing.

The designer has replied

@Officina23

Thank you - I see you have a lot of extra space above the printer, well done! ...and I see you printed it in PLA Galaxy, right? I have yet to try it but I already like it!

(Edited)

@hookuum

Replying to @Officina23 :

Usa

@hookuum

Replying to @Officina23 :

Flashforge petg in burnt titanium

@Ploide

Boosted

Print Profile

Corner Glass Riser (two colors)

great print, worked perfectly! I added a thin layer of foam to cushion the glass on the mounts too. thanks!

The designer has replied

@Officina23

Very nice with the same gray as the printer! What did you put on top of the glass? An IP camera? (the cable looks like a flat ethernet)

@Ploide

Boosted

Replying to @Officina23 :

It's a Wyze v3 Camera (available on Amazon) - I've found the WiFi on my X1C to be less than reliable (despite being very close to the AP) so that's a back up camera for me to be able to monitor the prints remotely, I just printed a bracket for it and added rubber feet to stop it sliding around with the vibrations.

@verdemarcomaker

Boosted

Print Profile

Corner Glass Riser (two colors)

the fastest riser to print... for now I'll leave it like this but in future I'll have to print a more complete riser to add the LEDs. good job. the lightest and fastest to print

The designer has replied

@Officina23

Thank you, being able to print it in a short time was the primary objective of this riser. (...magari potevo risponderti in italiano?)

@verdemarcomaker

Boosted

😂 piu che la velocità non avevo nemmeno abbastanza filamento per stampare il riser completo. ma ti dirò forse lo lascio cosi... vediamo se riesco a mettere una buona illuminazione sopra il vetro ... l'unico dubbio che mi viene è se magari al centro dei 4 lati non ci starebbe un altro "zoccolo" per sorreggere il peso? ho paura per il vetro

@ntran3450

Print Profile

Corner Glass Riser (single color)

Prints well and works as designed.

The designer has replied

@Officina23

Nice print!

@batmanwcm

Boosted

I was in the process of printing the more complicated Babo v1 AMS riser and came accross this. I realized that all I really needed was a simple lid riser that allows me the vent air out when printing PLA and PETG. Now I don't have to keep my door open when printing. This is just a simple and clean solution.

The designer has replied

@Officina23

Thank you

@CptSharki

Print Profile

Print on A1 mini - 0.24mm layer, 3 walls, 15% infill

works pretty good. 👍🏻

@Officina23

Thanks

@Vilius

Print Profile

Corner Glass Riser (two colors)

all is perfect

The designer has replied

@Officina23

Thank you

@ThatParksGuy

Print Profile

Corner Glass Riser (single color)

printed great! perfect fit.

The designer has replied

@Officina23

Thanks

@Tomer.Abadi

Boosted

Awesome model, fits well, super fast print, not a lot of material used. 5/5 :)

The designer has replied

@Officina23

Thank you

@gomez89

Print Profile

Corner Glass Riser (single color)

Lo he tenido para que le entre algo de aire pare imprimir en verano porque hace muchísima calor y el PLA se desforma dentro de la maquina y luego se atasca en el extrusor.

The designer has replied

@Officina23

Hola, lo imprimiste muy bien!

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.