Impossible Passthrough Egg by PrintingPopPop

PrintingPopPop

Toys & Games>Other Toys & Games

IP Report

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

Print by Object, 2-color AMS, 8mm brim

Designer

1.5 h

1 plate

4.9(63)

PLA, Adaptive layer height, Print By Object

1.5 h

1 plate

4.8(41)

Open in Bambu Studio

Boost

547

997

159

113

1.8 k

1.2 k

Released

Description

WELCOME

Welcome to another model found Exclusively here on Maker World. I'm not a professional full-time print farm or print designer. I have a day job and do this for the love of doing it. Please LIKE, COLLECT, and FOLLOW to see more of my work as it becomes available.

MODEL INFORMATION

This is a great model to put in plastic easter eggs instead of candy. Make them in different colors and let the kids match, trade, and share them. So simple, but so iconic.

Boost Me (for free)

Please leave a BOOST and a LIKE to support Maker World Exclusive creators like me. Your FREE support helps us to provide a continuous stream of free models for you, your friends, and your family to enjoy. Make sure to FOLLOW ME to see more free models as they are released. Check out my other models and collections below.

Check Out My Other Models and Collections HERE!

Comment & Rating (159)

@Digipo.eu

My bambu pla silk behaved strangely and crumbled in my hands :-(

The designer has replied

@3P_Designs

did it split at a single layer line or multiple layers? I think I have that same silk at home. were you using a X1C/P1S/P1P or A1/mini? I have a P1S and A1 so I can check either. that’s the first time I’ve seen that. how much of that silk have you run before?

@Digipo.eu

Replying to @3P_Designs :

hi, just pla basic everything is ok, I think it's a problem with plastic, because I asked friends who else has the same plastic, they say yes unfortunately pla silk two-color plastic can be thrown out from the Babmu company

@3P_Designs

Replying to @Digipo.eu :

I haven't had the best of luck either and the translucent PETG isn't my fav either. I've been rocking Polymer Silk and one from 3DHoJor off Amazon. As long as it's nice and dry, not issues. I also do manual calibrations and profiles for ALL non-Bambu filament. It takes a while but saves on the waste and headache later.

@thenewguy

Print Profile

Print by Object, 2-color AMS, 8mm brim

my aunt is in love with these! awesome print! what do you recommend cleaning the edges off with on the bottom where the brim was?

@3P_Designs

wow. good catch. was it an A1 or X1 hot end variant?

@thenewguy

Replying to @3P_Designs :

it was a P1S

@user_3895840251

Boosted

Print Profile

Print by Object, 2-color AMS, 8mm brim

good print. it does pass through completely! not much poop consumed either

@user_3895840251

Boosted

correction it does pass through

@3P_Designs

That should pass completely and easily. Make sure you removed all of the brim and look for any stringiness inside the white portion that it could be hanging up on. You probably just have burr on one of the pieces. I mean this model shoots through the body.

@user_4110829404

Boosted

Print Profile

PLA, Adaptive layer height, Print By Object

very fun!

@3P_Designs

Replying to @Spetz3D :

Love the pics

@zomb

Print Profile

Print by Object, 2-color AMS, 8mm brim

There are small artifacts on the overhangs (outer part of the egg, top of the cutouts at the bottom). Besides of that, nice model, thanks!

@3P_Designs

Thanks for the feedback. If you are printing more, try enabling adaptive layer heights and make sure it shrinks the height on those layers. The angle should be fine and the brim is there to keep the bottom from wobbling before it connects the egg belly, especially on an A1 or A1 mini. I do appreciate the honest constructive feedback.

@zomb

Replying to @3P_Designs :

Thanks for the tips! I’ll definitely try enabling adaptive layer heights next time. The artifacts aren’t a big issue, I just noticed them after closely examining my prints. They’re visible in the photos attached to the model description, so I wasn’t too concerned. Thanks again for the helpful advice!

@user_1370259816

Boosted

Print Profile

Print by Object, 2-color AMS, 8mm brim

supper fun! nieces and nephews are geting passthrough eggs😍

@3P_Designs

That's awesome. Happy Easter.

@leeseagle

Boosted

Print Profile

Print by Object, 2-color AMS, 8mm brim

I ended up sizing the print up a good bit but it printed perfectly. fun little egg. also if you put it in upside-down and pull the outer up super fast the inner spins like a top! family loves them.

@3P_Designs

Looks like Translucent PETG. Very nice.

@Cristi58

Print Profile

Print by Object, 2-color AMS, 8mm brim

Nice print!*Ext side -PLA+/Silk Sunlu (similar to PLA Silk bambu lab); *Int side- PLA basic-bambu lab; Thank you!

@3P_Designs

I haven’t tried Sunlu silks yet. I’ve stuck to Bambu (not a lot of options) and Polymaker.

@KWPuckett

Boosted

Print Profile

Print by Object, 2-color AMS, 8mm brim

Flawless print. I used the .16 optimal setting and Isanmate matte frosting cake filament.

@3P_Designs

Very smooth

@nana_2271545400

Print Profile

Print by Object, 2-color AMS, 8mm brim

love it!

@3P_Designs

very nice

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.