GIF
GIF
GIF
GIF
GIF
GIF

Yellow Artillery Tractor Fire Truck with Movements


Print Profile(1)

Ready to Print Profile with supports 0.2mm layer, 2 walls, 15% infill
Ready to Print Profile with supports 0.2mm layer, 2 walls, 15% infill
Designer
X1 Carbon, P1S, P1P, X1, X1E, A129.7 h
5.0

126
194
11
323
133
Released
Copyright Claim
Model
Comment & Rating
Remixes
Related Models

Model

This is an old school type of fire engine based on the Yellow Artillery Tractor Chassis model that I have released earlier. In that release itself I have explained how it is the universal platform on which various payloads can be added for specific function. This release contains the fire engine payload of the same.

 

I am very thankful to Mr Benoît Lussier for his feedbacks which has helped me refine the model further. Please Click Here to check out his make

 

 

If you have already downloaded and printed Yellow Artillery Tractor Chassis model, You would only need "Yellow AT Fire Truck Payload.3mf" file and Please skip to the title ASSEMBLY OF PAYLOAD.

There are three ways to print this.

  1. As single piece:- Please download STL file but there wont be any movements.
  2. Multiple Pieces :- Download 3mf file with Full_dismantled.3mf.BEST QUALITY OUTPUT. Please use the 3mf file for assembly also. CHECK EASE OF PRINTING TITLE BELOW
  3. Combined:- You may use any 3D viewer software like 3D builder in windows to merge components according to your printer and filaments. The sky is the limit for this. You may find a sample file ending with combined.3mf.

If you want to try TPU for tracks, you can download the "AT FireTruck TPU Tracks" which has the tracks and gears. You will need to replace all the gears and pinions in PLA version with the provided gear for TPU track working. but please note that I haven't tested them.

ASSEMBLY OF CHASSIS

ASSEMBLY OF PAYLOAD

Follow the GIF for assembly of payload.

MATING WITH CHASSIS

Follow the GIF for mating of payload with truck chassis. You can reuse the nut and bolt securing the Bed in the Yellow Artillery Tractor Chassis model to secure the payload. But you have to glue the nuts to the payload bed as shown in instructions.

Movements Included

  1. Engine Bay Cover Swing Open

NOTE The tolerances to some elements are zero which has been intentionally provided to friction lock the elements while not in movements. You may have to fine tune the tolerance from your end using scaling function in slicer to ensure good fit without compromising movements. This also applies for the pins that make rotation possible between elements. Please proceed with printing all the pins after testing printing a pin and testing the fit of a joint. You should be able to find the adequate scaling factor with this.

 

Appreciate the makes uploads. Open for suggestions.

 

 


Comment & Rating (11)

0/5000

Model Comment

nice looks

The designer has replied
1
Reply

Thanks man...

0
Reply

your welcome keep up the good work

0
Reply
Model Comment

How much work would it take to make this motorizeable?

The designer has replied
1
Reply

It won't be not that much work as fortunately this model already have the undercarriage cavity to place the dc motors and batteries. All the gears are free spinning also but the problem would be the tracks. These are not link chain tracks but similar to excavator rubber tracks without any meshing mechanisms in gears. For the tracks to work, there would be need of a meshing/locking mechanism between the tracks and the gears.

0
Reply
Model Comment

Very nice model and an impressive portfolio! I was looking for the black piece that sits on top of the tank behind the cabin inside the yellow frame and can't find it. May I make one suggestion , if you make a small dowel on the bottom of the seats and the holes for positioning the seat in the cabin floor it would make it easer to position the seats Perhaps also for the two leavers. Have you already tried to print the tracks out of TPU ?Thanks

The designer has replied
0
Reply

Thanks for the support bro. I will let you know the details in chat. please do see them.

0
Reply
Ready to Print Profile with supports 0.2mm layer, 2 walls, 15% infill

Alle part it easy to printe, Bambulab 1X C best printer. (Edited)

1
Reply
Model Comment

Blackjack, I'm enjoying your creations. Thanks. On the Yellow Fire Truck, I don't see the back of the cab partition. Is it possible to get a file for this ? My goal is to make every one of them. Thanks again. Alan

The designer has replied
0
Reply

Thanks for support bro. Really appreciate it. I will share the file in chat. Please do let me know if you need any more help with my models.

0
Reply
Model Comment

vvbb

0
Reply
No more

Remixes (0)

There are no remixes yet