Round chain print in place

Remixed by
Just say no to poop
Tools>Other Tools
IP Report

Round chain print in place

Remixed by
Just say no to poop
Boost
153
342
16

Print Profile(1)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1
0.28mm layer, 2 walls, 15% infill
0.28mm layer, 2 walls, 15% infill
Designer
5 h
2 plates
4.9(8)
Open in Bambu Studio
Boost
153
342
16
12
118
59
Released

Description

Make sure you have a clean plate before printing this. If you are having trouble printing it successfully, reduce to 50% print speed on your bambu printer after you start the print.

 

This is a unique and strong chain that is printed in place with minimal supports. Most chains that are printed in place have a flat part, but this is a true round chain link, printed interlocking. The support raft is not too much extra material and peels right off after printing. 

 

You might use this for a decoration or it's also just fun to play with as a fidget.

 

PLA or PETG will work, though PETG will be stronger. 

 

There are two plates with different sizes. If there is demand I can add more sizes. Enjoy!

 

 

chain
print in place

Comment & Rating (16)

(0/5000)
@say_no_to_poop
Here's the long chain while printing and then after removing the raft. It is 29" long, or 73.6cm!
2
Reply
@Firestarta
Boosted
Awesome! I increased top and bottom layers a little for strength. Printed in PLA+
2
Reply
@user_1653686562
Print Profile
0.28mm layer, 2 walls, 15% infill
Very nice!
1
Reply
@toxictrixx520
Boosted
Print Profile
0.28mm layer, 2 walls, 15% infill
Great for Cosplay
1
Reply
@say_no_to_poop
nice! what cosplay?
1
Reply
@toxictrixx520
Boosted
we have a non-profit Haunt and will be using them for several props and customs
1
Reply
@toxictrixx520
Boosted
Replying to @say_no_to_poop :
we have a Small haunted Trail and we are going to be using them a lot
0
Reply
@RekiBobby
Print Profile
0.28mm layer, 2 walls, 15% infill
Fantastic! Would love to see a larger/chunkier size.
1
Reply
@user_982244676
Boosted
Sweet
0
Reply
@user_1402308990
Print Profile
0.28mm layer, 2 walls, 15% infill
1
Reply
@say_no_to_poop
did you have any issues?
0
Reply
@Firestarta
Boosted
Print Profile
0.28mm layer, 2 walls, 15% infill
2
Reply
@user_3136905045
Print Profile
0.28mm layer, 2 walls, 15% infill
1
Reply
@Eric.p
Boosted
Print Profile
0.28mm layer, 2 walls, 15% infill
1
Reply

This remix is based on

Tensegrity Table (Remix)
Tensegrity Table (Remix)
Jim Larsen
Tensegrity Table (Remix)
Jim Larsen

License

This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike

Related Models

PRINT IN PLACE Large Hinged Box - 10 Compartments

PRINT IN PLACE Large Hinged Box - 10 Compartments

CosyCodes
8
311
325
Fabric Fidget V2 - Print in Place

Fabric Fidget V2 - Print in Place

Type1Printing
5
156
291
Print-in-place hinge

Print-in-place hinge

impl
0
101
59
Print in place Nunchucks

Print in place Nunchucks

YankeePrints
17
343
680
PrivacyTermsGuidelinesFAQCookie SettingsHot Searches
© 2025 MakerWorld