Poop Bucket for P1S/P1P/X1C (No Screws Needed)

Poop Bucket for P1S/P1P/X1C (No Screws Needed)

Boost
69
136
50

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

Better Fit, 0.2mm layer, 2 walls, 15% infill
Better Fit, 0.2mm layer, 2 walls, 15% infill
Designer
2 h
1 plate
5.0(7)

0.2mm layer, 2 walls, 10% infill
0.2mm layer, 2 walls, 10% infill
Designer
1.8 h
1 plate
4.8(28)

Taller Version, 0.2mm layer, 2 walls, 7% infill
Taller Version, 0.2mm layer, 2 walls, 7% infill
Designer
2.8 h
1 plate
4.5(4)

Open in Bambu Studio
Boost
69
136
50
33
426
327
Released

Description

This is a poop bucket that goes into the back of your printer. It press fits in, so it does not need any screws. When you put it in, make sure it is pushed against the bottom of the purge chute so it catches the poops properly. I recommend printing the tighter fit version because some people have had problems with it falling out due to vibrations. I found the original to work just fine on my P1S, but it might be different on the X1C

Boost Me (for free)

A boost is amazing, and its free!

 

Comment & Rating (50)

(0/5000)

Print Profile
0.2mm layer, 2 walls, 10% infill
Very nice and small file, everything fine withe the print! Bur you have to use double-sided tape to stick it to the case; over time the clamping weakens. This trash can with magnets will be top!
1
Reply
agreed I had to do the same or it just gradually (30seconds) popped right out
1
Reply
Replying to @user_637054353 :
The tighter fit version helps with your issue.
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
perfect fit and holds well without tape or screws
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
printed absolutely fine, but falls out of the back.
0
Reply
The tighter fit version helps with your issue
0
Reply
Replying to @CB__Studios :
I'll try that one next 😀
0
Reply
Print Profile
Taller Version, 0.2mm layer, 2 walls, 7% infill
occasionally false out of the poop Shute due to vibration.
0
Reply
You should try printing the tighter fit version
0
Reply
Boosted
A superb solution without unnecessary complexities
The designer has replied
Show original
0
Reply
Thanks!
0
Reply
Print Profile
Taller Version, 0.2mm layer, 2 walls, 7% infill
Currently using this to catch the filament poops. Works well. The wings fit in the chute quite well. Better than some of the purely magnetized versions I've seen/used in the past.
0
Reply
Thanks!
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
The body fits perfectly and holds
Show original
0
Reply
Thanks!
0
Reply
Print Profile
Better Fit, 0.2mm layer, 2 walls, 15% infill
looks good so far
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.