Trash Bag Holder

Trash Bag Holder

Boost
59
173
8

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

Large, 3.5 X 9 in. With Side Snap Lid
Large, 3.5 X 9 in. With Side Snap Lid
Designer
5.6 h
1 plate
5.0(1)

Small, 2.5 X 7 in. With SIde Snap Lid
Small, 2.5 X 7 in. With SIde Snap Lid
Designer
3.6 h
1 plate

All Options
All Options
Designer
12.1 h
4 plates

Open in Bambu Studio
Boost
59
173
8
5
52
38
Released

Description

It's a Trash Bag Holder!

 

I tried a few, but they didn't quite do what I wanted. Some were too short, some were huge, most had a slot that was way too big so when you get to the last few bags they all fall out instead of just 1. 

 

2-11-25

Big Update, I had some time to work on it this week, so I made a few modifications. The basic geometry is basically unchanged, but the big difference is a recessed snap ring inside the cylinder and a variety of snap in lids. 

 

And also a larger size for bigger trash bags. 

 

The new snap in lids hold strong enough to be placed upside down, if you prefer. I tested a variety of snap ring sizes, I'll upload the profile for all of them in case you want to try a different one. The one that snaps the full circumference of the lid holds the strongest, if you were going to mount it upside down that would be a very solid option. Although, my favorite is the one with a thumb ramp on the front, and snap in surfaces on the sides. 

 

I printed all these green ones in PETG HF, they turned out great, and are more flexible than PLA. I did one in PLA also, it's slightly snappier, if anything an even more secure hold on the lid. I imagine most filaments will work fine. 

 

 

Small Size:

  • .25" Exit Slot for the bags
  • 7 In. Overall Height
  • 2.5 in. Inside Diameter
  • 3 in. (75mm) and 100mm mounting holes
  • Also added a wide flat area to the back in case doublestick tape is your weapon of choice. 

 

Large Size:

  • The Same .25" Exit Slot
  • 9-3/8" Overall Height
  • 3.5 in. Inside Diameter
  • 3 in, (75mm) 100mm and 150mm (The hole spacing for shelves on my ikea cabinet is 50mm, so these always line up with a premade hole)
  • The Same wide flat area on the back for the trusty doublestick tape

 

 

 

Let me know if there's anything that could be improved. 

 

 

 

 

Enjoy!

Comment & Rating (8)

Please fill in your opinion
(0/5000)

It's now hanging under my kitchen sink, at the door. Great and fast print.
The designer has replied
1
Reply
Nice! glad you liked it
0
Reply
Boosted
The print profile is no longer public
Perfect, exactly what I was looking for, discreet, quick to print and robust. Thank you. However, should a lid be created, I would be delighted to upgrade this print, even if it is largely unnecessary
The designer has replied
Show original
0
Reply
Thank you! I will attempt to create a lid compatible with the original model
Show original
1
Reply
The first print of this turned out really well but it only fit my small bathroom trash bags. I enlarged it to make it fit my large kitchen bag rolls. Turned out perfect! I love the smaller slit for the bags to come out of. Definitely make it easier when the roll gets smaller. You don't accidentally pull the entire roll out towards the end.
The designer has replied
1
Reply
Thanks! Glad you liked it
0
Reply
You could easily scale it to your needs.
0
Reply
Print Profile
Large, 3.5 X 9 in. With Side Snap Lid
0
Reply
No more