Rolex GMT-Master II – Wall Clock by Sparco

Sparco

Household>Decor

IP Report

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

Pepsi version (PLA Basic)

Designer

6.9 h

3 plates

5.0(13)

Blue version (PLA Basic)

Designer

6.8 h

3 plates

5.0(3)

Red version (PLA Basic)

Designer

6.8 h

3 plates

4.8(5)

Green version (PLA Basic)

Designer

6.8 h

3 plates

5.0(4)

Open in Bambu Studio

Boost

211

325

393

169

Released

Description

Membership

Join

Now you can hang up a wall clock that is inspired by the Rolex GMT-Master II!

The bezel and dial can be connected without screws. Simply push the two parts into each other. For the second hand, you must remove the small black pin from the Clock Kit second hand. Then push the black pin through the printed second hand.

The GMT hand must be fitted directly after the hour hand and adjusted by hand. You can then display two time zones!

Please note that this model has been shared for non-commercial, personal use only.

Also check out my other wall clocks!

Rolex Submariner: https://makerworld.com/en/models/978569

Rolex Explorer Vintage: https://makerworld.com/en/model/1036551

Patek Philippe Nautilus: https://makerworld.com/en/models/1133027

Tudor Back Bay 58: https://makerworld.com/en/models/966249

Tudor Pelagos FXD: https://makerworld.com/en/models/907526

Omega x Swatch MoonSwatch: https://makerworld.com/en/models/1076101

Mondaine Railway Clock: https://makerworld.com/en/models/1098669

If you value my work and would like to continue supporting me, you could buy me a coffee. Any help is appreciated!

Boost Me (for free)

If you have extra boosts to spare, I’d truly appreciate your support. Your boost will help me continue sharing unique, niche models for the community to enjoy. Thank you very much!

Bill of Materials

Maker’s Supply Kits and Parts

Clock Components Kit-MH011

MH011

8.00 USD

× 1

Bambu Filaments

Black

A00-K0-1.75-1000-SPLFREE

19.99 USD

× 1

Silver

A00-D1-1.75-1000-SPLFREE

19.99 USD

× 1

Jade White

A00-W1-1.75-1000-SPLFREE

19.99 USD

× 1

Red

A00-R0-1.75-1000-SPLFREE

19.99 USD

× 1

Blue

A00-B9-1.75-1000-SPLFREE

19.99 USD

× 1

Bambu Green

A00-G6-1.75-1000-SPLFREE

19.99 USD

× 1

Buy Now

Download BOM

Comment & Rating (53)

@3dprintmike

beautiful print, came out great. only issue I had was with the hands. they were too small for my clock mechanism. ended up using one of the hands from the kit came with instead,

The designer has replied

@Sparco

Looks good! Which clock mechanism did you use?

@3dprintmike

Replying to @Sparco :

https://www.amazon.ca/dp/B0C414MSRV?ref=ppx_yo2ov_dt_b_fed_asin_title

@Sparco

Replying to @3dprintmike :

I can see that it has slightly larger dimensions than the Clock Kit MH011. That's why the hands don't fit. Perhaps you can scale the hands a little in Bambu Studio? The difference should be minimal.

@Joey3d

Boosted

Print Profile

Blue version (PLA Basic)

amazing prints love these, used the bambu lab clock device to make them working clocks and are perfect amazing! A*

@Sparco

Looks fantastic! You can place the GMT hand directly on the hour hand!

@Joey3d

Boosted

with the clock bits I got i couldn't fit thr gmt hand on, or I struggled abit with it

@samueleangori5

Print Profile

Pepsi version (PLA Basic)

crazy model!!

@Sparco

looks fantastic!

@L2daX

I have no idea how to assemble the hands. They don’t work for me and are too close together The hole in the hour hand is much too large, the hole in the minute hand too small

(Edited)

Show original

@user_423925675

that doesn’t look like the bambu clock kit

@JackM

Boosted

I used a non Bambu clock kit and had to make the hand holes bigger. The specs are different on different clock mechanisms. Bambu kit arrived, and the hands fit on it perfectly.

@3dprintmike

Print Profile

Green version (PLA Basic)

11/10 - amazing print

@Sparco

looks good!

@founfou

Boosted

Print Profile

Blue version (PLA Basic)

I'll never be late again with this large clock face Thanks

Show original

@Sparco

looks fantastic! maybe a little big for your wrist 🤣

@Chicag089

Boosted

Already printed a second one! Absolutely brilliant 🤩

Show original

@JackM

Boosted

Print Profile

Pepsi version (PLA Basic)

Turned out great! I used a different clock mechanism (not Bambu) and I had to make the hand holes a tiny bit bigger. All worked great, though.

@Frous

Boosted

Great design, easy to print!

@nairb3D

Print Profile

Red version (PLA Basic)

Waiting on clock components but came out great. Another nice addition to my wall.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Get Commercial License